How to homebrew an xbox 360 how to#
How to homebrew an xbox 360 install#
How to homebrew an xbox 360 code#

We need to solder 7 wires to the mother board. So we now have 8 pieces of wires, and each has 25cm in length. Use a scissor or utility knife to cut it in half (25 cm x 2). GitHub - pinh3ad/Xbox-360-Homebrew: Xbox 360 homebrew repository for testing, research, and development.

How to homebrew an xbox 360 code#

All code uses LibXenon, the free, open source, and legal development library for the Xbox 360. All code is from scratch with a few snippets taken from other projects. The supplied flat cable is 4-conductor and 50cm in length. Xbox 360 homebrew repository for testing, research, and development. We will be soldering the grey flat cable on your mother board, so let’s prepare them. You will also see a few female to female jumper wires, put them aside, we will use them later on. Open the buffered JTAG bundle, you will see a PCB board with chips on it, this is the JTAG board. We need to prepare the wires which will be soldered on to your XBOX 360 motherboard. You first need to disassemble your XBOX 360, there are tons of instructions on the internet, so I am not going to cover it here. (The NAND should be read out anyway, doesn't matter which Mainboard-Revision you have). With Jasper, beginning MFR July 2009, you have to read out the NAND first anyway to know for sure that the Hack will work. It is possible to use the hack up to Version 7371, but starting with Dashboard-Version 8xxx it isn't possible anymore. This is relatively easy, check the power connector: This buffered JTAG board is a native 3.3v device, so it is much safer. The parallel port is TTL data, which is 5V, but your NAND uses 3.3v, so a homemade unbuffered cable could damage your NAND. The benefit of using this buffered jtag board is, the data is buffered so it is much reliable then the unbuffered one.

360 Flash Tool ( currently Version 0.91).

MD5 Comparison Tool (hex editors can do this).

Infectus NAND Checker (currently Version 1.1).

Buffered XBOX 360 JTAG bundle (buy it from here).

In order to finish this task, you need to prepare the following tools/components:

How to homebrew an xbox 360 how to#

In this tutorial I am going to show you how to modify your XBOX 360 to run Xell Homebrew or xbox rebooter kernel.

4 Which Dashboard-Version does my console have? Select the Configure Now option, and confirm that you want to erase any existing data on the device.

3 How do I know my XBOX 360 is hackable?.

i highly suggest that you take off the metal case it sits in so that you can access the bottom of the motherboard. When the case is removed it should look like the picture.

first you need to completely take apart you 360 there are plenty of guides to do that so i wont cover it here. Opening your xbox 360's shell will void its warranty. Soldering irons can be very hot and cause burns, as well as possibly break your Xbox 360. ***Disclaimer: I am not liable for any damage that may be caused to your property or self from following the instructions in this tutorial. Wires (x12 this will be your LPT cable so make them long)Ī program to read the NAND (i used nandprob 2 you can find it HERE) Modchip (i will be using the coolrunner from team-xecuter)

How to homebrew an xbox 360 install#

To perform this RGH and utilize the exploit what you will need to do is read the NAND, install the modchip, write the NAND and installing your dash board of choice (i will be using xexmenu). Usually it would do exactly that however if the single is sent when it is booting up it allows us to run unsigned code. Basically what the RGH does is send a single to the processor that tells it to reset. When I started looking for a way to hack my 360 I heard about the jtag method only to find out that my dashboard was newer then 7371, but in early September a hardware exploit was developed know as the RGH. If you want to hack your Xbox 360 and your dashboard version is over 7371 then the only way that you can hack it is with the reset glitch hack (RGH).